Alison Parker
FV Capt. Bob
FV Capt. Bob
Alison Parker
FV Capt. Joe
FV Capt. Joe
Alison Parker
FV Patricia M
Alison Parker
FV Lyndon Johnson
FV Lyndon Johnson
Alison Parker
FV Orion
FV Orion

Vessels

FV Capt. Bob

Price Reduction: $450,000 (Hull Only)

Features

VESSEL TYPE
Steel Pelagic Longline

DIMENSIONS
L 67.3’ x W 21’0" x D 8.5’

HULL
1988 Bayou La Batre, AL

FUEL CAPACITY
5,000 gallons

ENGINE
Twin Turbo CAT 3406B, 350 HP apiece
Port rebuild 2021 – 2500 hrs
Starboard rebuild 2023 – 500 hrs
New generator – 4700 hrs

TRANSMISSION
Twin Disc 314 with gears with a 3:1 reduction, twin 1-part 3” diameter x 14ft long Aquamet 22 stainless steel driveshafts, no kort nozzles, twin 4-blade bronze propellers, ZF electronic engine controls, and hydraulic steering powered by independent main-engine drive hydraulic pump.

KEY FEATURES
• Fish hold capacity: 40,000 lbs
• Bait freezer capacity: 5,000 lbs
• Two ton (per day) ice maker - One Quality Marine with Toshiba compressor and Maja chiller tubes filled with 404 Freon.  installed beneath cover on work deck’s forward end.
• Radio Buoy rack with 8 beacons in place along portside bulwarks/margin deck. One more beacon in rack on set out house.
• MSB Buoy signal system with desktop monitor on port side bulwarks/margin deck.

Request the Survey

Photography & Videography by Burke Multimedia

FV Capt. Joe

Features

VESSEL TYPE
Steel Fish Dragger

DIMENSIONS
81.6’ x 24.0’ x 12.7'

HULL
1977, Theodore, AL

FUEL CAPACITY
9,000 Gallons

ENGINE
• Cat D-379 (650 HP). Complete engine overhaul in February 2024 ($85,000)
• This engine is air started, keel cooled, and turbo charged, and provided with a low lube oil pressure and low coolant water level alarm. The exhaust system is of the dry vertical type exiting the aft engine room.
• The front end of the engine is provided with a Marco
DC-26 power take off with three (3) hydraulic pumps attached which provides power for operation of deck machinery. The engine provides power through a Caterpillar 7241 marine reverse/reduction gear to a 5” shaft.

KEY FEATURES

• Star Link for phone and Internet service
• KVH Satellite TV
• added a Keel Cooler pipe for a 3306 Hydraulic Engine only  with 350HP
• F/V Capt Joe was hauled out at Roses Marine on completed on March 26, 2024

Request the Survey

Photography by Halsey Fulton

FV Patricia M

Features

VESSEL TYPE
Steel Fish & Scallop Dragger

DIMENSIONS
78’ LOA x 22’ x 12’

HULL
1979 – Deep Sea Boat Builders Inc., Hull Number 111

ENGINE
• Cat 3412
• Drive Gear: Caterpillar Reduction Gear MG 5.92:1 ratio installed new in May of 2021 with cable engine controls, 5” two-piece drive shaft and hydraulic steering.

Request the Survey

Photography by Halsey Fulton

FV Lyndon Johnson

Features

VESSEL TYPE
Fiberglass Scallop/Fish Dragger

DIMENSIONS
L 49' x W 16’1" x D 4’8"'

HULL
1990 Novi / 49

FUEL CAPACITY
500 gallons

HOLD CAPACITY
30,000 lbs

ENGINE
Caterpillar 3406 (450 HP) (11,000 hours)

KEY FEATURES
• Includes winch, frame and 8 foot Bluefleet drag
• Includes pogo mast and boom with 14” hauler

Request the Survey

 
 
 

FV Orion

Features

VESSEL TYPE
Steel Fish Dragger

DIMENSIONS
81.6’ x 24.0’ x 12.7'

HULL
1979, Bayou LaBatre, AL

FUEL CAPACITY

12,300 Gallons

ENGINE
Cat D-398 (825 HP)
• This engine is air start, keel cooled, and turbo charged and has low lube oil pressure and low coolant water alarms. The exhaust system is of the dry vertical type exiting aft in the engine room. 
• The front end of the engine is provided with Marco power take off with hydraulic pumps attached for operation of deck machinery
• The engine provides power output through a Caterpillar Model 3192 reverse/reduction gear with a 1.0:1 ratio through a single shaft with bulkhead packing gland to a four (4) blade propeller in a fixed nozzle arrangement

KEY FEATURES

• Starlink
• New John Deer 4045 Generator ($37,500)
• Ice Maker - makes 5 tons a day ($85,000)
• New Pair of H30 pullmaster Winch engines ($80,000)
• All new Electric motors purchased at Pinehill
• Vessel was hauled out  on March 18, 2024

Request the Survey

Photography + Videography by Halsey Fulton

FV Princess Laura

Features

VESSEL TYPE
Steel Fish Dragger

DIMENSIONS
84.1’ x 24.8’ x 12.2'

HULL
1978, Fort George Island, FL

FUEL CAPACITY
9,000 Gallons

ENGINE
• Cat 398 (850 HP)
• The engine is air started, keel cooled and fitted with dry vertical exhaust exiting the engine room on the centerline 
• The aft end of the engine is fitted with a Caterpillar Model 7251 reverse/reduction gear with a 3.95:1 ratio turning an 6” steel shaft supported by inline bearings through shaft alley

KEY FEATURES

• Time zero and Starlink
• Complete engine overhaul on Cat 3406 winch engine
• 2 new generators - Cat 3304 & Perkins X1300 (2024)
• New ice maker - 5 tons per day ($85,000)
• New fish gutting machine ($160,000)
• Updated 2 new net reels with 525 hydraulic motors
• Interior was completely remodeled  with electrical work.
• Comes Complete with nets and spare doors.

Request the Survey

Photography + Videography by Halsey Fulton

FV Harmony

Features

Features

VESSEL TYPE
Steel Fish Dragger

DIMENSIONS
85.3' x 24.0' x 11.6'

HULL
1988 Bayou LaBatre, Alabama

FUEL CAPACITY
12,000 Gallons

ENGINE
• Cat 3512 (1280 HP)
• Rebuilt Reintjes, reverse/reduction gear Model WAF 760 with a 5.75:1 ratio, that was installed in 2014
• Hydraulic power is supplied by a Caterpillar Model 3406 marine diesel engine, serial number 4TB06656, rated at 480 HP, mounted in the forward engine room on centerline between the two (2) generators

KEY FEATURES
• Hauled March 2024 with $80,000 in retrofits
• Star link for phone & internet
• Skymate
• Time zero
• Federal Permit available with Multi-species qualifier, black sea bass, scup, monkfish D and non-trap lobster for $100,000 additional.

Request the Survey

PERMIT AVAILABLE

 
 
 
 

Photography + Videography by Halsey Fulton

FV Tyler

FV Tyler

Features

Features

VESSEL TYPE
Steel Fish Dragger

DIMENSIONS
63.2’ x 21’ x 10.5'

HULL
1980, East Boothbay, Maine

FUEL CAPACITY
5,000 Gallons

ENGINE
• Cat 3412 (492 HP)
• Main is 32 VDC electric start, fresh water keel cooled with dry exhaust drives a reported 4 blade bronze propeller on a 4” stainless steel shaft through 
• Twin Disc MG 5202 reverse/reduction gear at a 5.04:1 ratio

KEY FEATURES
• Federal Permit available with Multi-species qualifier and non-trap lobster for $40,000 additional.

Request the Survey

 

Photography + Videography by Halsey Fulton

FV Atlantic Queen

Price Reduction: $295,000 (Hull Only)

Features

VESSEL TYPE
Fiberglass Fish Dragger

DIMENSIONS
Reg L 62.7’ LOA 68’ x W 19.8’ x D 8.5’

HULL
1980, DESCO Marine, St. Augustine, FL

FUEL CAPACITY
9,500 Gallons

ENGINE
Cummins KT 19 (425 HP)

KEY FEATURES + UPDATES

October 2024 Improvements ($18,000)
• Replaced steel under gallows both sides with stainless steel
• Painted rails and gallows frames  
• Replaced zincs
• Resealed entire after-deck with epoxy grit mix
• New window in the head
• New forward windows

Request the Survey

Permits Available

Videography + Photography by Halsey Fulton

FV Travis Natalie

Features

VESSEL TYPE
Fish & Scallop Dragger

DIMENSIONS
L 77’ x W 22’0" x D 12’

HULL
1984 Bayou La Batre, AL

FUEL CAPACITY
14,000 gallons

ENGINE
Caterpillar 3412 (675 HP) (Complete rebuild in 2018)

Request the Survey

Photography by Halsey Fulton

FV Terri-Ann

Features

VESSEL TYPE
Offshore Lobster & Crab

DIMENSIONS
L 65.0' x W 18.0' x D 7.0' (65.0' LOA)

HULL
1987 Washburn & Doughty, East Boothbay Harbor, Maine

FUEL CAPACITY
3,000 gallons total capacity

HOLD CAPACITY
12,000 to 14,000 lbs refrigerated sea-water capacity

ENGINE
Caterpillar C-18 (454 HP)

Request the Survey

Videography + Photography by Halsey Fulton

FV Shelby Ann

Features

VESSEL TYPE
Steel Fish Dragger

DIMENSIONS
L 64.8” x W 22' x D 10.3'

HULL
1979, St Augustine Trawlers, FL

FUEL CAPACITY
10,000 Gallons

HOLD CAPACITY
80,000 lbs

ENGINE
Cat 3412E (600 HP @ 2200 RPMS)

Request the Survey

Permits Available

Videography + Photography by Halsey Fulton

FV Excalibur

Features

VESSEL TYPE
Steel Fish Dragger

DIMENSIONS
L 72.7' x W 22.4' x D 10.9’ (78.0’ LOA)

HULL
1979 RYSCO (Blountstown, FL)

FUEL CAPACITY
12,000 gallons total capacity

ENGINE
Caterpillar 3412 (764 HP)

Request the Survey

Photography by Halsey Fulton

FV Miss Freya

Features

VESSEL TYPE
Offshore Lobster & Crab

DIMENSIONS
L 88.4' x W 25.0' x D 12.5’ (105.0’ LOA)

HULL
2001 Bayou LaBatre, AL

FUEL CAPACITY
36,000 gallons total capacity - (18,000 gallons currently used in forward tanks)

HOLD CAPACITY
35,000 to 40,000 refrigerated sea-water capacity

ENGINE
Caterpillar 3508

Request the Survey

Photography by Halsey Fulton

FV Vickie II

Features

VESSEL TYPE
Fish & Scallop Dragger w Part-time Scallop Permit

DIMENSIONS
L 74’4" x W 23’0" x D 12’2"

HULL
1998 – Ocean Marine Inc, Bayou La Batre AL

FUEL CAPACITY
10,000 gallons

ENGINE
1998 Caterpillar 3412 (540 HP)
Masson RCD 320 with 5.85:1 ratio

FEATURES & RECENT UPGRADES
Includes a Part-Time Scallop Permit (see below)

Request the Survey

Includes Part-Time Scallop Permit

 

Photography + Video by Halsey Fulton

FV Debbie Ann

FV Two Anns

Take a 3D Tour of Two Anns

Click play to take a virtual tour through the boat, including the engine room, fish hold, and main cabin. Select anywhere on the image to move to that section and see it in more detail, or click on the search icon to move to a new area of the boat.

Features

VESSEL TYPE
Steel Fish Dragger

DIMENSIONS
51.5’ x 18.0’ x 8.8’

HULL
1998 Bayou LaBatre, Alabama

FUEL CAPACITY
3,000 gallons

ENGINE
Cat 3406 (400 HP)

Request the Survey

Photography by Halsey Fulton

FV Market Price

FV Market Price

PRICE REDUCTION: $1,500,000

Take a 3D Tour of Market Price

Click play to take a virtual tour through the boat, including the engine room, fish hold, and main cabin. Select anywhere on the image to move to that section and see it in more detail, or click on the search icon to move to a new area of the boat.

Features

VESSEL TYPE
Fiberglass Tuna Yacht & Scallop Dragger

DIMENSIONS
54.0’ x 17.5’ x 6’

HULL
2017 Wesmac, Surrey Maine

FUEL CAPACITY
1,800 gallons

ENGINE
Cat C18 (803 HP) — 12,000 hours

KEY FEATURES

  • New Main Engine cooler in 2020

  • Touch Screen and Manual electronics package

  • Sat TV

  • Private Captains Stateroom

  • New zincs and bottom paint Jan of 2022

  • Large insulated fish hold easily reconverted back to 49 crate lobster tank

  • Extensive Durabrite Lights package

Request the Survey

Photography + Video by Halsey Fulton

FV Rebecca-Ann Naomi

Features

VESSEL TYPE
Wood Gillnet & Lobster

DIMENSIONS
47.6 x 16.2 x 7.3 —

ENGINE
Detroit Diesel (250 HP)

HULL
1976, Linwood Parker, Harkers Island

Federal Fishery Permit

• Monkfish C and Area 2 Lobster
• Max Baseline 45 feet X 480 HP

Request the Survey

 

Photography + Video by Halsey Fulton

FV Nordic Explorer

PRICE: $1,150,000

Features

Upgrades & Retrofits

Vessel Type
Fish Dragger

Dimensions
112.0’ (LOA) X 30’ X 10.5'

Hull
1984 Bender Shipbuilding, Mobile AL

Fuel Capacity
14,761 gallons

Engine
Cat D3516

Spring 2019
Complete refit ($900,000) including:
• Electrical work ($150,000)
• Fishing Gear including new nets ($175,000)
• Engine and generator repairs & upgrades ($150,000)
• Painted & upgrades to living area and pilot house ($150,000)

Summer 2019
• Overhaul of RSW tanks & refrigeration ($140,000)
• Hydraulic repairs ($160,000)

2020
• Addition of Marport wireless trawl monitoring system ($140,000)

Request the Survey

Photography by Halsey Fulton

 

Subscribe for advance notice of our newest listings

Sign up with your email address and phone number to receive updates.